Chemical Safety Data Sheet MSDS / SDS
2-Piperidineethanol
Revision Date:2026-03-21Revision Number:1
Product identifier
- Product name: 2-Piperidineethanol
- CBnumber: CB5127357
- CAS: 1484-84-0
- EINECS Number: 216-059-2
- Synonyms: 2-(2-HYDROXYETHYL)PIPERIDINE;(S)-2-Piperidineethanol
Relevant identified uses of the substance or mixture and uses advised against
- Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
- Uses advised against: none
Company Identification
- Company: Chemicalbook
- Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
- Telephone: 010-86108875
GHS Label elements, including precautionary statements
-
Symbol(GHS)
- Signal wordDanger
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continuerinsing.
P303+P361+P353 IF ON SKIN (or hair): Remove/Take off Immediately all contaminated clothing. Rinse SKIN with water/shower.
P301+P312 IF SWALLOWED: call a POISON CENTER or doctor/physician IF you feel unwell.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P260 Do not breathe dust/fume/gas/mist/vapours/spray.
Hazard statements
H314 Causes severe skin burns and eye damage
Substance
- Product name: 2-Piperidineethanol
- Synonyms: 2-(2-HYDROXYETHYL)PIPERIDINE;(S)-2-Piperidineethanol
- CAS: 1484-84-0
- EC number: 216-059-2
- MF: C7H15NO
- MW: 129.2
4.1 Description of first-aid measures
General adviceFirst aiders need to protect themselves. Show this material safety data sheet to the doctor in attendance.
If inhaled
After inhalation: fresh air. Immediately call in physician. If breathing stops: immediately apply artificial respiration, if necessary also oxygen.
In case of skin contact
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower. Call a physician immediately.
In case of eye contact
After eye contact: rinse out with plenty of water. Immediately call in ophthalmologist.
Remove contact lenses.
If swallowed
Remove contact lenses.
After swallowing: make victim drink water (two glasses at most), avoid vomiting (risk of perforation). Call a physician immediately. Do not attempt to neutralise.
4.2 Most important symptoms and effects, both acute and delayed
The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11
4.3 Indication of any immediate medical attention and special treatment needed
No data available
4.4 Notes to physician
No data available
5.1 Extinguishing media
Suitable extinguishing mediaWater Foam Carbon dioxide (CO2) Dry powder
Unsuitable extinguishing media
For this substance/mixture no limitations of extinguishing agents are given.
5.2 Special hazards arising from the substance or mixture
Carbon oxides
Nitrogen oxides (NOx)
Combustible.
Vapors are heavier than air and may spread along floors.
Forms explosive mixtures with air on intense heating.
Development of hazardous combustion gases or vapours possible in the event of fire.
Nitrogen oxides (NOx)
Combustible.
Vapors are heavier than air and may spread along floors.
Forms explosive mixtures with air on intense heating.
Development of hazardous combustion gases or vapours possible in the event of fire.
5.3 Advice for firefighters
Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.
Suppress (knock down) gases/vapors/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system.
Suppress (knock down) gases/vapors/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system.
NFPA 704
1
1
0
| HEALTH | 1 | Exposure would cause irritation with only minor residual injury (e.g. acetone, sodium bromate, potassium chloride) | |
| FIRE | 1 | Materials that require considerable preheating, under all ambient temperature conditions, before ignition and combustion can occur. Includes some finely divided suspended solids that do not require heating before ignition can occur. Flash point at or above 93.3 °C (200 °F). (e.g. mineral oil, ammonia) | |
| REACT | 0 | Normally stable, even under fire exposure conditions, and is not reactive with water (e.g. helium,N2) | |
| SPEC. HAZ. |
6.1 Personal precautions, protective equipment and emergency procedures
Advice for non-emergency personnel: Avoid inhalation of dusts. Avoid substance contact.
Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.
For personal protection see section 8.
Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.
For personal protection see section 8.
6.2 Environmental precautions
Do not let product enter drains.
6.3 Methods and materials for containment and cleaning up
Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up dry. Dispose of properly. Clean up affected area. Avoid generation of dusts.
6.4 Reference to other sections
For disposal see section 13.
7.1 Precautions for safe handling
Advice on safe handlingWork under hood. Do not inhale substance/mixture.
Hygiene measures
Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.
For precautions see section 2.2.
For precautions see section 2.2.
7.2 Conditions for safe storage, including any incompatibilities
Storage conditionsTightly closed. Dry.
Storage class
Storage class (TRGS 510): 8A: Combustible, corrosive hazardous materials
8.1 Control parameters
Ingredients with workplace control parametersContains no substances with occupational exposure limit values.
8.2 Exposure controls
Appropriate engineering controlsImmediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.
Personal protective equipment
Eye/face protection
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Tightly fitting safety goggles
Skin protection
required
Body Protection
protective clothing
Respiratory protection
required when dusts are generated.
Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.
Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.
Control of environmental exposure
Do not let product enter drains.
Information on basic physicochemical properties
- a) Physical statesolid
- b) Colorwhite
- c) OdorMild, sweet, nauseating-floral, warm-herbaceous odor of moderate tenacity.
- d) Melting point/freezing pointMelting point/range: 38 - 40 °C - lit.
- e) Initial boiling point and boiling range234 °C - lit.
- f) Flammability (solid, gas)No data available
- g) Upper/lower flammability or explosive limitsNo data available
- h) Flash point112.8 °C - closed cup
- i) Autoignition temperatureNo data available
- j) Decomposition temperatureNo data available
- k) pHNo data available
- l) ViscosityViscosity, kinematic: No data available
Viscosity, dynamic: No data available - m) Water solubilitysoluble
- n) Partition coefficient n-octanol/waterNo data available
- o) Vapor pressure0.75-13.04Pa at 20-50℃
- p) Density1.010 g/cm3
- Relative density1.01
- q) Relative vapor densityNo data available
- r) Particle characteristicsNo data available
- s) Explosive propertiesNo data available
- t) Oxidizing propertiesNo data available
- SolubilityChloroform, Methanol
9.2 Other safety information
No data available
10.1 Chemical stability
The product is chemically stable under standard ambient conditions (room temperature) .
10.2 Possibility of hazardous reactions
No data available
10.3 Conditions to avoid
Avoid moisture.
Strong heating.
Strong heating.
10.4 Incompatible materials
Strong oxidizing agents, Strong acids
10.5 Hazardous decomposition products
In the event of fire: see section 5
11.1 Information on toxicological effects
Acute toxicityOral: No data available
LC50 Inhalation - 4 h - 1.5 mg/l - dust/mist (Acute toxicity estimate)
LD50 Dermal - 1,100 mg/kg
Skin corrosion/irritation
LC50 Inhalation - 4 h - 1.5 mg/l - dust/mist (Acute toxicity estimate)
LD50 Dermal - 1,100 mg/kg
Remarks: No data available
Serious eye damage/eye irritation
Remarks: No data available
Respiratory or skin sensitization
Classified based on available data. For more details, see section 2
Germ cell mutagenicity
Classified based on available data. For more details, see section 2
Carcinogenicity
Classified based on available data. For more details, see section 2
Reproductive toxicity
Classified based on available data. For more details, see section 2
Specific target organ toxicity - single exposure
Classified based on available data. For more details, see section 2
Specific target organ toxicity - repeated exposure
Classified based on available data. For more details, see section 2
Aspiration hazard
Classified based on available data. For more details, see section 2
11.2 Additional Information
Material is extremely destructive to tissue of the mucous membranes and upper respiratory tract, eyes, and skin., spasm, inflammation and edema of the larynx, spasm, inflammation and edema of the bronchi, pneumonitis, pulmonary edema, burning sensation, Cough, wheezing, laryngitis, Shortness of breath, Headache, Nausea
12.1 Toxicity
No data available
12.2 Persistence and degradability
No data available
12.3 Bioaccumulative potential
No data available
12.4 Mobility in soil
No data available
12.5 Results of PBT and vPvB assessment
PBT/vPvB assessment not available as chemical safety assessment not required/not conducted
12.6 Endocrine disrupting properties
No data available
12.7 Other adverse effects
No data available
13.1 Waste treatment methods
Product
Offer surplus and non-recyclable solutions to a licensed disposal company.
Offer surplus and non-recyclable solutions to a licensed disposal company.
14.1 UN number
ADR/RID: 3263
IMDG: 3263
IATA-DGR: 3263
IMDG: 3263
IATA-DGR: 3263
14.2 UN proper shipping name
ADR/RID: CORROSIVE SOLID, BASIC, ORGANIC, N.O.S. (2-Piperidin-2-ylethanol) (2-
Piperidin-2-ylethanol)
IMDG: CORROSIVE SOLID, BASIC, ORGANIC, N.O.S. (2-Piperidin-2-ylethanol) (2-
Piperidin-2-ylethanol)
IATA-DGR: Corrosive solid, basic, organic, n.o.s. (2-Piperidin-2-ylethanol) (2-Piperidin-2- ylethanol)
Piperidin-2-ylethanol)
IMDG: CORROSIVE SOLID, BASIC, ORGANIC, N.O.S. (2-Piperidin-2-ylethanol) (2-
Piperidin-2-ylethanol)
IATA-DGR: Corrosive solid, basic, organic, n.o.s. (2-Piperidin-2-ylethanol) (2-Piperidin-2- ylethanol)
14.3 Transport hazard class(es)
ADR/RID: 8
IMDG: 8
IATA-DGR: 8
IMDG: 8
IATA-DGR: 8
14.4 Packaging group
ADR/RID: II
IMDG: II
IATA-DGR: II
IMDG: II
IATA-DGR: II
14.5 Environmental hazards
ADR/RID: no
IMDG Marine pollutant: no
IATA-DGR: no
IMDG Marine pollutant: no
IATA-DGR: no
14.6 Special precautions for user
Based on chemical properties, choose appropriate tools and conditions of transport.
Transporting tools shall be equipped with appropriate and sufficient firefighting equipment and emergency leaking installations. If transporting by road, please go along the specified route.
Transporting tools shall be equipped with appropriate and sufficient firefighting equipment and emergency leaking installations. If transporting by road, please go along the specified route.
14.7 Incompatible materials
Strong oxidizing agents, Strong acids
15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
National regulatory information
Other regulations
Please pay attention on the waste treatment should also comply with local regulations requirement.
Other regulations
Please pay attention on the waste treatment should also comply with local regulations requirement.
Abbreviations and acronyms
CAS: Chemical Abstracts Service
TWA: Time-Weighted Average
STEL: Short-Term Exposure Limit
LD50: Lethal Dose 50%
LC50: Lethal Concentration 50%
EC50: Effective Concentration 50%
PEL: Permissible Exposure Limit
TLV: Threshold Limit Value
IMDG: International Maritime Dangerous Goods Code
IATA: International Air Transport Association
ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
DOT: US Department of Transportation
NFPA: National Fire Protection Association
NIOSH: National Institute for Occupational Safety and Health
OSHA: Occupational Safety and Health Administration
TWA: Time-Weighted Average
STEL: Short-Term Exposure Limit
LD50: Lethal Dose 50%
LC50: Lethal Concentration 50%
EC50: Effective Concentration 50%
PEL: Permissible Exposure Limit
TLV: Threshold Limit Value
IMDG: International Maritime Dangerous Goods Code
IATA: International Air Transport Association
ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
DOT: US Department of Transportation
NFPA: National Fire Protection Association
NIOSH: National Institute for Occupational Safety and Health
OSHA: Occupational Safety and Health Administration
Disclaimer:
The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.