Chemical Safety Data Sheet MSDS / SDS

Bis(2-ethylhexyl) phosphate

Revision Date:2026-03-21Revision Number:1

SECTION 1: Identification of the substance/mixture and of the company/undertaking

Product identifier

  • Product name: Bis(2-ethylhexyl) phosphate
  • CBnumber: CB4464040
  • CAS: 298-07-7
  • EINECS Number: 206-056-4
  • Synonyms: P-204 ;DI-(2-ETHYLHEXYL)PHOSPHORIC ACID

Relevant identified uses of the substance or mixture and uses advised against

  • Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
  • Uses advised against: none

Company Identification

  • Company: Chemicalbook
  • Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
  • Telephone: 010-86108875

SECTION 2: Hazards identification

GHS Label elements, including precautionary statements

  • Symbol(GHS)
  • Signal wordDanger
Precautionary statements
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P301+P330+P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P303+P361+P353 IF ON SKIN (or hair): Remove/Take off Immediately all contaminated clothing. Rinse SKIN with water/shower.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continuerinsing.
Hazard statements
H312 Harmful in contact with skin
H314 Causes severe skin burns and eye damage

SECTION 3: Composition/information on ingredients

Substance

  • Product name: Bis(2-ethylhexyl) phosphate
  • Synonyms: P-204 ;DI-(2-ETHYLHEXYL)PHOSPHORIC ACID
  • CAS: 298-07-7
  • EC number: 206-056-4
  • MF: C16H35O4P
  • MW: 322.42

SECTION 4: First aid measures

General advice

First aiders need to protect themselves. Show this safety data sheet to the doctor in attendance.

If inhaled

After inhalation: fresh air. Call in physician.

In case of skin contact

In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower. Call a physician immediately.

In case of eye contact

After eye contact: rinse out with plenty of water. Immediately call in ophthalmologist. Remove contact lenses.

If swallowed

After swallowing: make victim drink water (two glasses at most), avoid vomiting (risk of perforation). Call a physician immediately. Do not attempt to neutralise.

Most important symptoms and effects, both acute and delayed

The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11

Protection of first-aiders

For personal protection see section 8.

Notes to physician

No data available

SECTION 5: Firefighting measures

Suitable extinguishing media

Carbon dioxide (CO2) Foam Dry powder

Unsuitable extinguishing media

For this substance/mixture no limitations of extinguishing agents are given.

Specific hazards during fire fighting

Combustible. Vapours are heavier than air and may spread along floors. Forms explosive mixtures with air on intense heating. Development of hazardous combustion gases or vapours possible in the event of fire.

Hazardous combustion products

Carbon oxides Oxides of phosphorus

Specific extinguishing methods

Suppress (knock down) gases/vapours/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system.

Special protective equipment for fire-fighters

Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.

NFPA 704

2
1
0
HEALTH 2 Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury (e.g. diethyl ether, ammonium phosphate, iodine)
FIRE 1 Materials that require considerable preheating, under all ambient temperature conditions, before ignition and combustion can occur. Includes some finely divided suspended solids that do not require heating before ignition can occur. Flash point at or above 93.3 °C (200 °F). (e.g. mineral oil, ammonia)
REACT 0 Normally stable, even under fire exposure conditions, and is not reactive with water (e.g. helium,N2)
SPEC. HAZ.

SECTION 6: Accidental release measures

Personal precautions, protective equipment and emergency procedures

Advice for non-emergency personnel: Do not breathe vapours, aerosols. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert. Advice for emergency responders: For personal protection see section 8.

Environmental precautions

Do not let product enter drains.

Methods and materials for containment and cleaning up

Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up with liquid-absorbent material (e.g. Chemizorb® ). Dispose of properly. Clean up affected area.

SECTION 7: Handling and storage

Handling

Avoidance of contact
Metals Mild steel

Storage

Further information on storage conditions
Tightly closed.
Storage class
8A, Combustible, corrosive hazardous materials
Recommended storage temperature
Recommended storage temperature see product label.

SECTION 8: Exposure controls/personal protection

Ingredients with workplace control parameters

Contains no substances with occupational exposure limit values.

Engineering measures

No data available

Personal protective equipment

Respiratory protection
required when vapours/aerosols are generated.
Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.
Recommended Filter type
Filter type ABEK
The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.
Eye/face protection
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
Tightly fitting safety goggles
Skin and body protection
protective clothing
Hand protection
Material
Nitrile rubber
Break through time
480 min
Glove thickness
0.4 mm
Protective index
Full contact
Manufacturer
Camatril® (KCL 730 / Aldrich Z677442, Size M)
Material
Nitrile rubber
Break through time
30 min
Glove thickness
0.11 mm
Protective index
Splash contact
Manufacturer
KCL 741 L
Remarks
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D- 36124 Eichenzell, Internet: www.kcl.de).
Hygiene measures
Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.

SECTION 9: Physical and chemical properties

Information on basic physicochemical properties

  • Solubilityethanol: soluble100mg/mL, clear
  • Physical stateLiquid
  • Appearanceliquid
  • ColorColorless
  • OdorNo data available
  • Odor ThresholdNo data available
  • pH3 (< 1g/l, H2O)
  • Melting point/ range-60 °C
    Method: lit.
  • Boiling point/boiling range48 °C (12 mmHg)
  • Flash point130 °C
  • Evaporation rateNo data available
  • Flammability (solid, gas)No data available
  • Flammability (liquids)No data available
  • Burning rateNo data available
  • Upper explosion limit / Upper flammability limitNo data available
  • Lower explosion limit / Lower flammability limitNo data available
  • Vapor pressure<0.1 hPa (20 °C)
  • Relative vapor densityNo data available
  • Relative density0.965 g/mL at 25 °C(lit.)
  • Density0.965 g/cm3 (25 °C)
  • Water solubilityslightly soluble
  • Partition coefficient: n-octanol/waterNo data available
  • Autoignition temperatureNo data available
  • Decomposition temperatureNo data available
  • Viscosity, dynamicNo data available
  • Viscosity, kinematicNo data available
  • Flow timeNo data available
  • Explosive propertiesNo data available
  • Oxidizing propertiesNo data available
  • Molecular weight322.42 g/mol
  • Particle characteristics Particle sizeNo data available
  • Refractive index1.44

SECTION 10: Stability and reactivity

Reactivity

Forms explosive mixtures with air on intense heating. A range from approx. 15 Kelvin below the flash point is to be rated as critical.

Chemical stability

The product is chemically stable under standard ambient conditions (room temperature) .

Possibility of hazardous reactions

Violent reactions possible with: Strong oxidizing agents Strong bases

Conditions to avoid

Strong heating.

Incompatible materials

Metals Mild steel

Hazardous decomposition products

In the event of fire: see section 5

SECTION 11: Toxicological information

11.1 Information on toxicological effects

Acute toxicity
LD50 Oral - Rat - male and female - > 500 - < 5,000 mg/kg (OECD Test Guideline 401)
Inhalation: No data available
LD50 Dermal - Rabbit - male and female - > 2,000 mg/kg (OECD Test Guideline 402)
LD50 Intraperitoneal - Rat - 50 mg/kg
Remarks: Liver:Other changes.
Skin corrosion/irritation
Skin - Rabbit
Result: Corrosive
Remarks: (ECHA)
Serious eye damage/eye irritation
Eyes - Rabbit
Result: Corrosive - 24 h
Respiratory or skin sensitization
Classified based on available data. For more details, see section 2
Germ cell mutagenicity
Classified based on available data. For more details, see section 2
Test Type: Ames test
Test system: Salmonella typhimurium
Metabolic activation: with and without metabolic activation
Method: OECD Test Guideline 471
Result: negative
Test Type: In vitro mammalian cell gene mutation test
Test system: Mouse lymphoma test
Metabolic activation: with and without metabolic activation
Result: negative
Remarks: (ECHA)
Carcinogenicity
Classified based on available data. For more details, see section 2
Reproductive toxicity
Classified based on available data. For more details, see section 2
Specific target organ toxicity - single exposure
Classified based on available data. For more details, see section 2
Specific target organ toxicity - repeated exposure
Classified based on available data. For more details, see section 2
Aspiration hazard
Classified based on available data. For more details, see section 2

11.2 Additional Information

RTECS: TB7875000
To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated.
Material is extremely destructive to tissue of the mucous membranes and upper respiratory tract, eyes, and skin., spasm, inflammation and edema of the larynx, spasm, inflammation and edema of the bronchi, pneumonitis, pulmonary edema, burning sensation, Cough, wheezing, laryngitis, Shortness of breath, Headache,
Nausea
Material is extremely destructive to tissue of the mucous membranes and upper respiratory tract, eyes, and skin., spasm, inflammation and edema of the larynx, spasm, inflammation and edema of the bronchi, pneumonitis, pulmonary edema, burning sensation, Cough, wheezing, laryngitis, Shortness of breath, Headache,
Nausea

SECTION 12: Ecological information

Ecotoxicity

Components:

bis(2-ethylhexyl) hydrogen phosphate:

Toxicity to fish
LC50 (Oncorhynchus mykiss (rainbow trout)): 20 - 30 mg/l Exposure time: 96 h Test Type: static test Remarks: (ECHA)
Toxicity to daphnia and other aquatic invertebrates
EC50 (Daphnia magna (Water flea)): 80.3 mg/l Exposure time: 48 h Test Type: static test Remarks: (ECHA)
Toxicity to algae/aquatic plants
EC50 (Chlorella emersonii): 50 - 100 mg/l Exposure time: 48 h Test Type: Growth inhibition EC50 (Chlorella emersonii): 50 - 100 mg/l Exposure time: 48 h Test Type: Growth inhibition
Toxicity to fish (Chronic toxicity)
NOEC (Oncorhynchus mykiss (rainbow trout)): 20.6 mg/l End point: mortality Exposure time: 48 d Test Type: semi-static test Remarks: (ECHA)

Persistence and degradability

Components:

bis(2-ethylhexyl) hydrogen phosphate:

Biodegradability
aerobic Inoculum: activated sludge Result: Readily biodegradable. Biodegradation: 75 % Exposure time: 28 d Method: OECD Test Guideline 301F GLP: yes

Bioaccumulative potential

Components:

bis(2-ethylhexyl) hydrogen phosphate:

Bioaccumulation
Remarks: No data available

Mobility in soil

Components:

bis(2-ethylhexyl) hydrogen phosphate:

Stability in soil
Remarks: No data available

Other adverse effects

Components:

bis(2-ethylhexyl) hydrogen phosphate:

Additional ecological information
No data available

SECTION 13: Disposal considerations

Disposal methods

Waste from residues
Offer surplus and non-recyclable solutions to a licensed disposal company.

SECTION 14: Transport information

International Regulations

IATA-DGR

UN/ID No. : UN 1902
Proper shipping name : Diisooctyl acid phosphate
Class : 8
Packing group : III
Labels : Class 8 - Corrosive substances
Packing instruction (cargo aircraft) : 856
Packing instruction (passenger aircraft) : 852

IMDG-Code

UN number : UN 1902
Proper shipping name : DIISOOCTYL ACID PHOSPHATE
Class : 8
Packing group : III
Labels : 8
EmS Code : F-A, S-B
Marine pollutant : no

Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code

Not applicable for product as supplied.

National Regulations

JT/T 617

UN number : UN 1902
Proper shipping name : DIISOOCTYL ACID PHOSPHATE
Class : 8
Packing group : III
Labels : 8
Environmentally hazardous : no

Special precautions for user

The transport classification(s) provided herein are for informational purposes only, and solely based upon the properties of the unpackaged material as it is described within this Safety Data Sheet. Transportation classifications may vary by mode of transportation, package sizes, and variations in regional or country regulations.

SECTION 15: Regulatory information

National regulatory information

Regulations on Safety Management of Hazardous Chemicals

Catalogue of Hazardous Chemicals

Identification of Major Hazard Installations for Hazardous Chemicals (GB 18218)

Not listed

Hazardous Chemicals for Priority Management

Not listed under SAWS

Regulations on Labour Protection in Workplaces where Toxic Substances are Used

Catalogue of Highly Toxic Chemicals

Not listed

Regulation of Environmental Management on the First Import of Chemicals and the Import and Export of Toxic Chemicals

China Severely Restricted Toxic Chemicals for Import and Export

Not listed

Regulation on the Administration of Precursor Chemicals

Catalogue and Classification of Precursor Chemicals

Not listed

SECTION 16: Other information

Full text of other abbreviations

AIIC - Australian Inventory of Industrial Chemicals
ANTT - National Agency forTransport by Land of Brazil
ASTM - American Society for the Testing of Materials
bw - Body weight
CMR - Carcinogen, Mutagen or Reproductive Toxicant
DIN -Standard of the German Institute for Standardisation
DSL - Domestic SubstancesList (Canada)
ECx - Concentration associated with x% response
ELx - Loading rate associated with x% response
EmS - Emergency Schedule
ENCS - Existing and NewChemical Substances (Japan)
ErCx - Concentration associated with x% growth rate response
ERG - Emergency Response Guide
GHS - Globally Harmonised System
GLP - Good Laboratory Practice
IARC - International Agency for Research on Can- cer
IATA - International Air Transport Association
IBC - International Code for theConstruction and Equipment of Ships carrying Dangerous Chemicals in Bulk
IC50 -Half maximal inhibitory concentration
ICAO - International Civil Aviation Organiza- tion
IECSC - Inventory of Existing Chemical Substances in China
IMDG - Interna- tional Maritime Dangerous Goods
IMO - International Maritime Organisation
ISHL -Industrial Safety and Health Law (Japan)
ISO - International Organisation forStandardisation
KECI - Korea Existing Chemicals Inventory
LC50 - Lethal Concen- tration to 50 % of a test population
LD50 - Lethal Dose to 50% of a test population (Median Lethal Dose)
MARPOL - International Convention for the Prevention of Pol- lution from Ships
MERCOSUR - The Agreement for the Facilitation of the Transport of Dangerous Goods
n.o.s. - Not Otherwise Specified
Nch - Chilean Norm
NO(A)EC - No Observed (Adverse) Effect Concentration
NO(A)EL - No Observed (Adverse) Ef- fect Level
NOELR - No Observable Effect Loading Rate
NOM - Official MexicanNorm
NTP - National Toxicology Program
NZIoC - New Zealand Inventory of Chem- icals
OECD - Organisation for Economic Co-operation and Development
OPPTS - Of- fice of Chemical Safety and Pollution Prevention
PBT - Persistent, Bioaccumulative and Toxic substance
PICCS - Philippines Inventory of Chemicals and Chemical Sub- stances
(Q)SAR - (Quantitative) Structure Activity Relationship
REACH - Regulation (EC) No 1907/2006 of the European Parliament and of the Council concerning theRegistration, Evaluation, Authorisation and Restriction of Chemicals
SADT - Self-Accelerating Decomposition Temperature
SDS - Safety Data Sheet
TCSI - TaiwanChemical Substance Inventory
TDG - Transportation of Dangerous Goods
TECI -Thailand Existing Chemicals Inventory
TSCA - Toxic Substances Control Act (UnitedStates)
UN - United Nations
UNRTDG - United Nations Recommendations on theTransport of Dangerous Goods
vPvB - Very Persistent and Very Bioaccumulative
WHMIS - Workplace Hazardous Materials Information System
Disclaimer:

The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.

Recommended Products
Triethyl phosphate SDS ISOOCTYL 3-MERCAPTOPROPIONATE SDS Calcium phosphate SDS 2-Ethylhexyl mercaptoacetate SDS Trisodium phosphate SDS Bis(2-ethylhexyl) sebacate SDS Zinc phosphate SDS Bis(2-ethylhexyl) maleate SDS Diisooctyl phthalate SDS Bis(2-ethylhexyl) phthalate SDS