Chemical Safety Data Sheet MSDS / SDS

Propiolic Acid

Revision Date:2026-03-21Revision Number:1

SECTION 1: Identification of the substance/mixture and of the company/undertaking

Product identifier

  • Product name: Propiolic Acid
  • CBnumber: CB8195906
  • CAS: 471-25-0
  • EINECS Number: 207-437-8
  • Synonyms: Propynoate

Relevant identified uses of the substance or mixture and uses advised against

  • Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
  • Uses advised against: none

Company Identification

  • Company: Chemicalbook
  • Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
  • Telephone: 010-86108875

SECTION 2: Hazards identification

GHS Label elements, including precautionary statements

  • Symbol(GHS)
  • Signal wordDanger
Precautionary statements
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continuerinsing.
P303+P361+P353 IF ON SKIN (or hair): Remove/Take off Immediately all contaminated clothing. Rinse SKIN with water/shower.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P233 Keep container tightly closed.
P210 Keep away from heat/sparks/open flames/hot surfaces. — No smoking.
Hazard statements
H314 Causes severe skin burns and eye damage
H310 Fatal in contact with skin
H301 Toxic if swalloed
H226 Flammable liquid and vapour

SECTION 3: Composition/information on ingredients

Substance

  • Product name: Propiolic Acid
  • Synonyms: Propynoate
  • CAS: 471-25-0
  • EC number: 207-437-8
  • MF: C3H2O2
  • MW: 70.05

SECTION 4: First aid measures

General advice

First aiders need to protect themselves. Show this material safety data sheet to the doctor in attendance.

If inhaled

After inhalation: fresh air. Call in physician.

In case of skin contact

In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower. Call a physician immediately.

In case of eye contact

After eye contact: rinse out with plenty of water. Immediately call in ophthalmologist. Remove contact lenses.

If swallowed

If swallowed: give water to drink (two glasses at most). Seek medical advice immediately. In exceptional cases only, if medical care is not available within one hour, induce vomiting (only in persons who are wide awake and fully conscious), administer activated charcoal (20 - 40 g in a 10% slurry) and consult a doctor as quickly as possible. Do not attempt to neutralise.

Most important symptoms and effects, both acute and delayed

The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11

Protection of first-aiders

For personal protection see section 8.

Notes to physician

No data available

SECTION 5: Firefighting measures

Unsuitable extinguishing media

For this substance/mixture no limitations of extinguishing agents are given.

Specific hazards during fire fighting

Vapors are heavier than air and may spread along floors. Forms explosive mixtures with air at elevated temperatures.

Hazardous combustion products

Carbon oxides

Specific extinguishing methods

Remove container from danger zone and cool with water. Prevent fire extinguishing water from contaminating surface water or the ground water system.

Special protective equipment for fire-fighters

Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.

NFPA 704

3
2
0
HEALTH 3 Short exposure could cause serious temporary or moderate residual injury (e.g. liquid hydrogen, sulfuric acid, calcium hypochlorite, hexafluorosilicic acid)
FIRE 2 Must be moderately heated or exposed to relatively high ambient temperature before ignition can occur and multiple finely divided suspended solids that do not require heating before ignition can occur. Flash point between 37.8 and 93.3 °C (100 and 200 °F). (e.g. diesel fuel, sulfur)
REACT 0 Normally stable, even under fire exposure conditions, and is not reactive with water (e.g. helium,N2)
SPEC. HAZ.

SECTION 6: Accidental release measures

Personal precautions, protective equipment and emergency procedures

Advice for non-emergency personnel: Do not breathe vapors, aerosols. Avoid substance contact. Ensure adequate ventilation. Keep away from heat and sources of ignition. Evacuate the danger area, observe emergency procedures, consult an expert. Advice for emergency responders: For personal protection see section 8.

Environmental precautions

Do not let product enter drains. Risk of explosion.

Methods and materials for containment and cleaning up

Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up carefully with liquid-absorbent material . Dispose of properly. Clean up affected area.

SECTION 7: Handling and storage

Handling

Advice on protection against fire and explosion
Keep away from open flames, hot surfaces and sources of ignition. Take precautionary measures against static discharge.
Avoidance of contact
Bases Oxidizing agents Reducing agents

Storage

Further information on storage conditions
Keep container tightly closed in a dry and wellventilated place. Keep away from heat and sources of ignition. Keep locked up or in an area accessible only to qualified or authorized persons.
Storage class
3, Flammable liquids
Recommended storage temperature
2 - 8 °C
Packaging material
Suitable material: Poly Drum

SECTION 8: Exposure controls/personal protection

Ingredients with workplace control parameters

Contains no substances with occupational exposure limit values.

Engineering measures

No data available

Personal protective equipment

Respiratory protection
required when vapours/aerosols are generated.
Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.
Recommended Filter type
Filter type ABEK
The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.
Eye/face protection
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
Tightly fitting safety goggles
Skin and body protection
Flame retardant antistatic protective clothing.
Hand protection
Remarks
required
Hygiene measures
Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.

SECTION 9: Physical and chemical properties

Information on basic physicochemical properties

  • SolubilityChloroform (Soluble), Methanol (Soluble)
  • Physical stateLiquid After Melting
  • Particle characteristics Particle sizeNo data available
  • Molecular weight70.05 g/mol
  • Oxidizing propertiesNo data available
  • Explosive propertiesNo data available
  • Flow timeNo data available
  • Viscosity, kinematicNo data available
  • Viscosity, dynamicNo data available
  • Decomposition temperatureNo data available
  • Autoignition temperatureNo data available
  • Partition coefficient: n-octanol/waterNo data available
  • Water solubilitymiscible
  • Density1.138 g/cm3 (25 °C)
    Method: lit.
  • Relative density1.138 g/mL at 25 °C (lit.)
  • Relative vapor densityNo data available
  • Vapor pressureNo data available
  • Lower explosion limit / Lower flammability limitNo data available
  • Upper explosion limit / Upper flammability limitNo data available
  • Burning rateNo data available
  • Flammability (liquids)No data available
  • Flammability (solid, gas)No data available
  • Evaporation rateNo data available
  • Flash point58 °C
    Method: closed cup
  • Boiling point/boiling range102 °C (267 hPa)
    Method: lit.
  • Melting point/ range16 - 18 °C
    Method: lit.
  • pHNo data available
  • Odor ThresholdNo data available
  • OdorNo data available
  • Colordark yellow
  • Appearanceclear, liquid

SECTION 10: Stability and reactivity

Reactivity

Vapor/air-mixtures are explosive at intense warming.

Chemical stability

The product is chemically stable under standard ambient conditions (room temperature) .

Possibility of hazardous reactions

No data available

Conditions to avoid

Heating.

Incompatible materials

Bases Oxidizing agents Reducing agents

Hazardous decomposition products

In the event of fire: see section 5

SECTION 11: Toxicological information

11.1 Information on toxicological effects

Acute toxicity
Acute toxicity estimate Oral - 100 mg/kg (Calculation method)
LD50 Oral - Rat - 100 mg/kg
Remarks: (RTECS)
Symptoms: mucosal irritations, Cough, Shortness of breath, Possible damages:, damage of respiratory tract
Acute toxicity estimate Dermal - 100 mg/kg (Calculation method)
LD50 Dermal - Guinea pig - 100 mg/kg
Remarks: (RTECS)
Skin corrosion/irritation
Remarks: Causes skin burns.
(ECHA)
Serious eye damage/eye irritation
Remarks: Causes serious eye damage.
Respiratory or skin sensitization
Classified based on available data. For more details, see section 2
Germ cell mutagenicity
Classified based on available data. For more details, see section 2
Carcinogenicity
Classified based on available data. For more details, see section 2
Reproductive toxicity
Classified based on available data. For more details, see section 2
Specific target organ toxicity - single exposure
Classified based on available data. For more details, see section 2
Specific target organ toxicity - repeated exposure
Classified based on available data. For more details, see section 2
Aspiration hazard
Classified based on available data. For more details, see section 2

11.2 Additional Information

RTECS: UD9300000
Material is extremely destructive to tissue of the mucous membranes and upper respiratory tract, eyes, and skin., Cough, Shortness of breath, Headache, Nausea
To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated.
Other dangerous properties can not be excluded.
Handle in accordance with good industrial hygiene and safety practice.

SECTION 12: Ecological information

Ecotoxicity

No data available

Persistence and degradability

No data available

Bioaccumulative potential

No data available

Mobility in soil

No data available

Other adverse effects

Components:

Acetylenemonocarboxylic acid:

Additional ecological information
Discharge into the environment must be avoided.

SECTION 13: Disposal considerations

Disposal methods

Waste from residues
Offer surplus and non-recyclable solutions to a licensed disposal company.

SECTION 14: Transport information

International Regulations

IATA-DGR

UN/ID No. : UN 2920
Proper shipping name : Corrosive liquid, flammable, n.o.s.
(Acetylenemonocarboxylic acid)
Class : 8
Subsidiary risk : 3
Packing group : II
Labels : Class 8 - Corrosive substances, Class 3 - Flammable liquids
Packing instruction (cargo aircraft) : 855
Packing instruction (passenger aircraft) : 851

IMDG-Code

UN number : UN 2920
Proper shipping name : CORROSIVE LIQUID, FLAMMABLE, N.O.S.
(Acetylenemonocarboxylic acid)
Class : 8
Subsidiary risk : 3
Packing group : II
Labels : 8 (3)
EmS Code : F-E, S-C
Marine pollutant : no

Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code

Not applicable for product as supplied.
National regulation GB 6944/12268
UN number : UN 2920
Proper shipping name : CORROSIVE LIQUID, FLAMMABLE, N.O.S.
(Acetylenemonocarboxylic acid)
Class : 8
Subsidiary risk : 3
Packing group : II
Labels : 8 (3)

Special precautions for user

The transport classification(s) provided herein are for informational purposes only, and solely based upon the properties of the unpackaged material as it is described within this Safety Data Sheet. Transportation classifications may vary by mode of transportation, package sizes, and variations in regional or country regulations.

SECTION 15: Regulatory information

Downstream users need to comply with the conditions of safe use of the chemical, understand the environmental and health hazard and risk management measures identified on the SDS as well as the local/national regulations concerning the chemical.

National regulatory information

Regulations on Safety Management of Hazardous Chemicals

Catalogue of Hazardous Chemicals

Identification of Major Hazard Installations for Hazardous Chemicals (GB 18218)

No. / Code Chemical name / Category Threshold quantity

J5 Acute toxic 500 t

W5.4 Flammable liquids 5,000 t

Hazardous Chemicals for Priority Management

Not listed under SAWS

Regulations on Occupational Labor Protection in the at workplaces where

Toxic Substances Are Used

Catalogue of Highly Toxic Chemicals

Not listed

Regulation of Environmental Management on the First Import of Chemicals and the Import and Export of Toxic Chemicals

China Severely Restricted Toxic Chemicals for Import and Export

Not listed

Measures on the Environmental Administration of New Chemical Substances Registration

Registration/Notification number

B1A222232991

SECTION 16: Other information

Full text of other abbreviations

AIIC - Australian Inventory of Industrial Chemicals
ANTT - National Agency forTransport by Land of Brazil
ASTM - American Society for the Testing of Materials
bw - Body weight
CMR - Carcinogen, Mutagen or Reproductive Toxicant
DIN -Standard of the German Institute for Standardisation
DSL - Domestic SubstancesList (Canada)
ECx - Concentration associated with x% response
ELx - Loading rate associated with x% response
EmS - Emergency Schedule
ENCS - Existing and NewChemical Substances (Japan)
ErCx - Concentration associated with x% growth rate response
ERG - Emergency Response Guide
GHS - Globally Harmonized System
GLP - Good Laboratory Practice
IARC - International Agency for Research on Can- cer
IATA - International Air Transport Association
IBC - International Code for theConstruction and Equipment of Ships carrying Dangerous Chemicals in Bulk
IC50 -Half maximal inhibitory concentration
ICAO - International Civil Aviation Organiza- tion
IECSC - Inventory of Existing Chemical Substances in China
IMDG - Interna- tional Maritime Dangerous Goods
IMO - International Maritime Organization
ISHL -Industrial Safety and Health Law (Japan)
ISO - International Organisation forStandardization
KECI - Korea Existing Chemicals Inventory
LC50 - Lethal Concen- tration to 50 % of a test population
LD50 - Lethal Dose to 50% of a test population (Median Lethal Dose)
MARPOL - International Convention for the Prevention of Pol- lution from Ships
n.o.s. - Not Otherwise Specified
Nch - Chilean Norm
NO(A)EC -No Observed (Adverse) Effect Concentration
NO(A)EL - No Observed (Adverse) Ef- fect Level
NOELR - No Observable Effect Loading Rate
NOM - Official MexicanNorm
NTP - National Toxicology Program
NZIoC - New Zealand Inventory of Chem- icals
OECD - Organization for Economic Co-operation and Development
OPPTS - Of- fice of Chemical Safety and Pollution Prevention
PBT - Persistent, Bioaccumulative and Toxic substance
PICCS - Philippines Inventory of Chemicals and Chemical Sub- stances
(Q)SAR - (Quantitative) Structure Activity Relationship
REACH - Regulation (EC) No 1907/2006 of the European Parliament and of the Council concerning theRegistration, Evaluation, Authorisation and Restriction of Chemicals
SADT - Self-Accelerating Decomposition Temperature
SDS - Safety Data Sheet
TCSI - TaiwanChemical Substance Inventory
TDG - Transportation of Dangerous Goods
TECI -Thailand Existing Chemicals Inventory
TSCA - Toxic Substances Control Act (UnitedStates)
UN - United Nations
UNRTDG - United Nations Recommendations on theTransport of Dangerous Goods
vPvB - Very Persistent and Very Bioaccumulative
WHMIS - Workplace Hazardous Materials Information System
Disclaimer:

The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.

Recommended Products
Hyaluronic acid SDS TERT-BUTYL PROPIOLATE SDS Methyl propiolate SDS Ascoric Acid SDS METHYL 2-BUTYNOATE SDS Stearic acid SDS Folic acid SDS Phenylpropiolic acid SDS Ethyl propiolate SDS Propiolic Acid SDS