Chemical Safety Data Sheet MSDS / SDS
DEOXYCHOLIC ACID SODIUM SALT MONOHYDRATE
Revision Date:2026-03-21Revision Number:1
Product identifier
- Product name: DEOXYCHOLIC ACID SODIUM SALT MONOHYDRATE
- CBnumber: CB3360804
- CAS: 145224-92-6
- EINECS Number: 680-423-0
- Synonyms: SODIUM DEOXYCHOLATE MONOHYDRATE;GO (3α,5β,12α)
Relevant identified uses of the substance or mixture and uses advised against
- Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
- Uses advised against: none
Company Identification
- Company: Chemicalbook
- Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
- Telephone: 010-86108875
GHS Label elements, including precautionary statements
-
Symbol(GHS)
- Signal wordWarning
No data available
Hazard statements
H302 Harmful if swallowed
Substance
- Product name: DEOXYCHOLIC ACID SODIUM SALT MONOHYDRATE
- Synonyms: SODIUM DEOXYCHOLATE MONOHYDRATE;GO (3α,5β,12α)
- CAS: 145224-92-6
- EC number: 680-423-0
- MF: C24H41NaO5
- MW: 432.57
4.1 Description of first-aid measures
General adviceConsult a physician. Show this material safety data sheet to the doctor in attendance.
If inhaled
If breathed in, move person into fresh air. If not breathing, give artificial respiration.
Consult a physician.
In case of skin contact
Consult a physician.
Wash off with soap and plenty of water. Consult a physician.
In case of eye contact
Flush eyes with water as a precaution.
If swallowed
Never give anything by mouth to an unconscious person. Rinse mouth with water. Consult a physician.
4.2 Most important symptoms and effects, both acute and delayed
The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11
4.3 Indication of any immediate medical attention and special treatment needed
No data available
4.4 Notes to physician
No data available
5.1 Extinguishing media
Suitable extinguishing mediaUse water spray, alcohol-resistant foam, dry chemical or carbon dioxide.
5.2 Special hazards arising from the substance or mixture
Carbon oxides
Sodium oxides
Sodium oxides
5.3 Advice for firefighters
Wear self-contained breathing apparatus for firefighting if necessary.
NFPA 704
2
1
0
| HEALTH | 2 | Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury (e.g. diethyl ether, ammonium phosphate, iodine) | |
| FIRE | 1 | Materials that require considerable preheating, under all ambient temperature conditions, before ignition and combustion can occur. Includes some finely divided suspended solids that do not require heating before ignition can occur. Flash point at or above 93.3 °C (200 °F). (e.g. mineral oil, ammonia) | |
| REACT | 0 | Normally stable, even under fire exposure conditions, and is not reactive with water (e.g. helium,N2) | |
| SPEC. HAZ. |
6.1 Personal precautions, protective equipment and emergency procedures
Use personal protective equipment. Avoid dust formation. Avoid breathing vapors, mist or gas. Ensure adequate ventilation. Avoid breathing dust.
For personal protection see section 8.
For personal protection see section 8.
6.2 Environmental precautions
Do not let product enter drains.
6.3 Methods and materials for containment and cleaning up
Pick up and arrange disposal without creating dust. Sweep up and shovel. Keep in suitable, closed containers for disposal.
6.4 Reference to other sections
For disposal see section 13.
7.1 Precautions for safe handling
Advice on safe handlingAvoid contact with skin and eyes. Avoid formation of dust and aerosols.
Advice on protection against fire and explosion
Provide appropriate exhaust ventilation at places where dust is formed.
Hygiene measures
Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday.
For precautions see section 2.2.
For precautions see section 2.2.
7.2 Conditions for safe storage, including any incompatibilities
Storage conditionsKeep container tightly closed in a dry and well-ventilated place.
Store under inert gas.
Storage class
Store under inert gas.
Storage class (TRGS 510): 11: Combustible Solids
8.1 Control parameters
Ingredients with workplace control parametersContains no substances with occupational exposure limit values.
8.2 Exposure controls
Appropriate engineering controlsHandle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday.
Personal protective equipment
Eye/face protection
Safety glasses with side-shields conforming to EN166 Use equipment for eye protection tested and approved under appropriate government standards such as
NIOSH (US) or EN 166(EU).
NIOSH (US) or EN 166(EU).
Skin protection
Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands.
The selected protective gloves have to satisfy the specifications of Regulation (EU) 2016/425 and the standard EN 374 derived from it.
Full contact
Material: Nitrile rubber
Minimum layer thickness: 0.11 mm
Break through time: 480 min
Material tested: (KCL 740 / Aldrich Z677272, Size M)
Splash contact
Material: Nitrile rubber
Minimum layer thickness: 0.11 mm
Break through time: 480 min
Material tested: (KCL 740 / Aldrich Z677272, Size M) data source: KCL GmbH, D-36124 Eichenzell, phone +49 (0)6659 87300, e-mail sales@kcl.de, test method: EN374
If used in solution, or mixed with other substances, and under conditions which differ from EN 374, contact the supplier of the EC approved gloves. This recommendation is advisory only and must be evaluated by an industrial hygienist and safety officer familiar with the specific situation of anticipated use by our customers. It should not be construed as offering an approval for any specific use scenario.
The selected protective gloves have to satisfy the specifications of Regulation (EU) 2016/425 and the standard EN 374 derived from it.
Full contact
Material: Nitrile rubber
Minimum layer thickness: 0.11 mm
Break through time: 480 min
Material tested: (KCL 740 / Aldrich Z677272, Size M)
Splash contact
Material: Nitrile rubber
Minimum layer thickness: 0.11 mm
Break through time: 480 min
Material tested: (KCL 740 / Aldrich Z677272, Size M) data source: KCL GmbH, D-36124 Eichenzell, phone +49 (0)6659 87300, e-mail sales@kcl.de, test method: EN374
If used in solution, or mixed with other substances, and under conditions which differ from EN 374, contact the supplier of the EC approved gloves. This recommendation is advisory only and must be evaluated by an industrial hygienist and safety officer familiar with the specific situation of anticipated use by our customers. It should not be construed as offering an approval for any specific use scenario.
Body Protection
Complete suit protecting against chemicals, The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace.
Respiratory protection
For nuisance exposures use type P95 (US) or type P1 (EU EN 143) particle respirator.For higher level protection use type OV/AG/P99 (US) or type ABEK-P2 (EU
EN 143) respirator cartridges. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU).
EN 143) respirator cartridges. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU).
Control of environmental exposure
Do not let product enter drains.
Information on basic physicochemical properties
- a) Physical statesolid
- b) ColorNo data available
- c) OdorNo data available
- d) Melting point/freezing pointNo data available
- e) Initial boiling point and boiling rangeNo data available
- f) Flammability (solid, gas)No data available
- g) Upper/lower flammability or explosive limitsNo data available
- h) Flash pointNo data available
- i) Autoignition temperatureNo data available
- j) Decomposition temperatureNo data available
- k) pH7.5 - 9.5 at 43.3 g/l at 25 °C
- l) ViscosityViscosity, kinematic: No data available
Viscosity, dynamic: No data available - m) Water solubilityca.43.3 g/l at 20 °C
- n) Partition coefficient n-octanol/waterNo data available
- o) Vapor pressureNo data available
- p) DensityNo data available
- Relative densityNo data available
- q) Relative vapor densityNo data available
- r) Particle characteristicsNo data available
- s) Explosive propertiesNo data available
- t) Oxidizing propertiesNo data available
- SolubilityH2O: 0.1 M at 20 °C, clear, colorless
- Absorption≤0.08 at 280 in H2O at 0.1M
≤0.10 at 260 in H2O at 0.1M
9.2 Other safety information
No data available
10.1 Chemical stability
Stable under recommended storage conditions.
10.2 Possibility of hazardous reactions
No data available
10.3 Conditions to avoid
No data available
10.4 Incompatible materials
Oxidizing agents
10.5 Hazardous decomposition products
In the event of fire: see section 5
11.1 Information on toxicological effects
Acute toxicityLD50 Oral - Rat - 1,370 mg/kg
Remarks: (External MSDS)
Inhalation: No data available
Dermal: No data available
Skin corrosion/irritation
Remarks: (External MSDS)
Inhalation: No data available
Dermal: No data available
Remarks: No data available
Serious eye damage/eye irritation
Remarks: No data available
Respiratory or skin sensitization
Classified based on available data. For more details, see section 2
Germ cell mutagenicity
Classified based on available data. For more details, see section 2
Carcinogenicity
Classified based on available data. For more details, see section 2
Reproductive toxicity
Classified based on available data. For more details, see section 2
Specific target organ toxicity - single exposure
Classified based on available data. For more details, see section 2
Specific target organ toxicity - repeated exposure
Classified based on available data. For more details, see section 2
Aspiration hazard
Classified based on available data. For more details, see section 2
11.2 Additional Information
To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated.
12.1 Toxicity
No data available
12.2 Persistence and degradability
No data available
12.3 Bioaccumulative potential
No data available
12.4 Mobility in soil
No data available
12.5 Results of PBT and vPvB assessment
PBT/vPvB assessment not available as chemical safety assessment not required/not conducted
12.6 Endocrine disrupting properties
No data available
12.7 Other adverse effects
No data available
13.1 Waste treatment methods
Product
Offer surplus and non-recyclable solutions to a licensed disposal company. Dissolve or mix the material with a combustible solvent and burn in a chemical incinerator equipped with an afterburner and scrubber.
Contaminated packaging
Offer surplus and non-recyclable solutions to a licensed disposal company. Dissolve or mix the material with a combustible solvent and burn in a chemical incinerator equipped with an afterburner and scrubber.
Dispose of as unused product.
14.1 UN number
ADR/RID: -
IMDG: -
IATA-DGR: -
IMDG: -
IATA-DGR: -
14.2 UN proper shipping name
ADR/RID: Not dangerous goods
IMDG: Not dangerous goods
IATA-DGR: Not dangerous goods
IMDG: Not dangerous goods
IATA-DGR: Not dangerous goods
14.3 Transport hazard class(es)
ADR/RID: -
IMDG: -
IATA-DGR: -
IMDG: -
IATA-DGR: -
14.4 Packaging group
ADR/RID: -
IMDG: -
IATA-DGR: -
IMDG: -
IATA-DGR: -
14.5 Environmental hazards
ADR/RID: no
IMDG Marine pollutant: no
IATA-DGR: no
IMDG Marine pollutant: no
IATA-DGR: no
14.6 Special precautions for user
14.7 Incompatible materials
Oxidizing agents
Further information: Not classified as dangerous in the meaning of transport regulations.
Further information: Not classified as dangerous in the meaning of transport regulations.
15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
National regulatory information
Measures on the Environmental Administration of New Chemical Substances Registration
Registration/Notification number : B1A222214039
Downstream users need to comply with the conditions of safe use of the chemical, understand the environmental and health hazard and risk management measures identified on the SDS as well as the local/national regulations concerning the chemical.
Other regulations
Please pay attention on the waste treatment should also comply with local regulations requirement.
Measures on the Environmental Administration of New Chemical Substances Registration
Registration/Notification number : B1A222214039
Downstream users need to comply with the conditions of safe use of the chemical, understand the environmental and health hazard and risk management measures identified on the SDS as well as the local/national regulations concerning the chemical.
Other regulations
Please pay attention on the waste treatment should also comply with local regulations requirement.
Abbreviations and acronyms
CAS: Chemical Abstracts Service
TWA: Time-Weighted Average
STEL: Short-Term Exposure Limit
LD50: Lethal Dose 50%
LC50: Lethal Concentration 50%
EC50: Effective Concentration 50%
PEL: Permissible Exposure Limit
TLV: Threshold Limit Value
IMDG: International Maritime Dangerous Goods Code
IATA: International Air Transport Association
ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
DOT: US Department of Transportation
NFPA: National Fire Protection Association
NIOSH: National Institute for Occupational Safety and Health
OSHA: Occupational Safety and Health Administration
TWA: Time-Weighted Average
STEL: Short-Term Exposure Limit
LD50: Lethal Dose 50%
LC50: Lethal Concentration 50%
EC50: Effective Concentration 50%
PEL: Permissible Exposure Limit
TLV: Threshold Limit Value
IMDG: International Maritime Dangerous Goods Code
IATA: International Air Transport Association
ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
DOT: US Department of Transportation
NFPA: National Fire Protection Association
NIOSH: National Institute for Occupational Safety and Health
OSHA: Occupational Safety and Health Administration
Disclaimer:
The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.