Chemical Safety Data Sheet MSDS / SDS

SODIUM ACETATE-13C2

Revision Date:2026-03-21Revision Number:1

SECTION 1: Identification of the substance/mixture and of the company/undertaking

Product identifier

Product name: SODIUM ACETATE-13C2
CBnumber: CB2205542
CAS: 56374-56-2
Synonyms: SODIUM ACETATE (1,2-13C2);13C Labeled sodium acetate

Relevant identified uses of the substance or mixture and uses advised against

Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
Uses advised against: none

Company Identification

Company: Chemicalbook
Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
Telephone: 010-86108875

SECTION 2: Hazards identification

GHS Label elements, including precautionary statements

Symbol(GHS) No data available

Signal wordNo data available

Precautionary statements

No data available

Hazard statements

No data available

SECTION 3: Composition/information on ingredients

Substance

Product name: SODIUM ACETATE-13C2
Synonyms: SODIUM ACETATE (1,2-13C2);13C Labeled sodium acetate
CAS: 56374-56-2
MF: C2H3NaO2
MW: 84.05

SECTION 4: First aid measures

4.1 Description of first-aid measures

If inhaled

After inhalation: fresh air.

In case of skin contact

In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower.

In case of eye contact

After eye contact: rinse out with plenty of water. Remove contact lenses.

If swallowed

After swallowing: make victim drink water (two glasses at most). Consult doctor if feeling unwell.

4.2 Most important symptoms and effects, both acute and delayed

The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11

4.3 Indication of any immediate medical attention and special treatment needed

No data available

SECTION 5: Firefighting measures

5.1 Extinguishing media

Suitable extinguishing media

Water Foam Carbon dioxide (CO2) Dry powder

Unsuitable extinguishing media

For this substance/mixture no limitations of extinguishing agents are given.

5.2 Special hazards arising from the substance or mixture

Carbon oxides
Sodium oxides
Combustible.
Development of hazardous combustion gases or vapours possible in the event of fire.

5.3 Advice for firefighters

In the event of fire, wear self-contained breathing apparatus.

5.4 Further information

Suppress (knock down) gases/vapors/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system.

SECTION 6: Accidental release measures

6.1 Personal precautions, protective equipment and emergency procedures

Advice for non-emergency personnel: Avoid inhalation of dusts. Evacuate the danger area, observe emergency procedures, consult an expert.
For personal protection see section 8.

6.2 Environmental precautions

Do not let product enter drains.

6.3 Methods and materials for containment and cleaning up

Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up dry. Dispose of properly. Clean up affected area. Avoid generation of dusts.

6.4 Reference to other sections

For disposal see section 13.

SECTION 7: Handling and storage

7.1 Precautions for safe handling

For precautions see section 2.2.

7.2 Conditions for safe storage, including any incompatibilities

Storage conditions

Tightly closed. Dry.
hygroscopic

Storage class

Storage class (TRGS 510): 11: Combustible Solids

7.3 Specific end use(s)

Apart from the uses mentioned in section 1.2 no other specific uses are stipulated

SECTION 8: Exposure controls/personal protection

8.1 Control parameters

Ingredients with workplace control parameters

8.2 Exposure controls

Personal protective equipment

Eye/face protection

Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses

Skin protection

This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell,
Internet: www.kcl.de).
Full contact
Material: Nitrile rubber
Minimum layer thickness: 0,11 mm
Break through time: 480 min
Material tested:KCL 741 L
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell,
Internet: www.kcl.de).
Splash contact
Material: Nitrile rubber
Minimum layer thickness: 0,11 mm
Break through time: 480 min
Material tested:KCL 741 L

Respiratory protection

required when dusts are generated.
Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.
Recommended Filter type: Filter type P1
The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer.
These measures have to be properly documented.

Control of environmental exposure

Do not let product enter drains.

SECTION 9: Physical and chemical properties

Information on basic physicochemical properties

a) Physical statepowder
b) Colorwhite
c) OdorNo data available
d) Melting point/freezing pointMelting point/ range: > 300 °C - dec.
e) Initial boiling point and boiling rangeNo data available
f) Flammability (solid, gas)No data available
g) Upper/lower flammability or explosive limitsNo data available
h) Flash pointNot applicable
i) Autoignition temperatureNo data available
j) Decomposition temperatureNo data available
k) pHNo data available
l) ViscosityViscosity, kinematic: No data available
Viscosity, dynamic: No data available
m) Water solubilityNo data available
n) Partition coefficient n-octanol/waterNo data available
o) Vapor pressureNo data available
p) DensityNo data available
Relative densityNo data available
q) Relative vapor densityNo data available
r) Particle characteristicsNo data available
s) Explosive propertiesNo data available
t) Oxidizing propertiesnone
SolubilityMethanol (Slightly), Water (Soluble)

9.2 Other safety information

No data available

SECTION 10: Stability and reactivity

10.1 Reactivity

The following applies in general to flammable organic substances and mixtures: in correspondingly fine distribution, when whirled up a dust explosion potential may generally be assumed.

10.2 Chemical stability

The product is chemically stable under standard ambient conditions (room temperature) .

10.3 Possibility of hazardous reactions

Risk of explosion with: nitrates
Exothermic reaction with:
Fluorine

10.4 Conditions to avoid

Avoid moisture.
no information available

10.5 Incompatible materials

No data available

10.6 Hazardous decomposition products

In the event of fire: see section 5

SECTION 11: Toxicological information

11.1 Information on toxicological effects

Acute toxicity

LD50 Oral - Rat - male and female - 2.700 mg/kg (OECD Test Guideline 401)
Remarks: (ECHA)
The value is given in analogy to the following substances: sodium acetate
LC50 Inhalation - Rat - male and female - 4 h - > 5,6 mg/l - dust/mist (OECD Test Guideline 403)
Remarks: The value is given in analogy to the following substances: sodium acetate
LD50 Dermal - Rabbit - female - > 20.000 mg/kg (OECD Test Guideline 402)
Remarks: The value is given in analogy to the following substances: sodium acetate

Skin corrosion/irritation

Skin - Rabbit
Result: No skin irritation - 4 h (OECD Test Guideline 404)
Remarks: The value is given in analogy to the following substances: sodium acetate

Serious eye damage/eye irritation

Eyes - Rabbit
Result: No eye irritation - 24 h (OECD Test Guideline 405)
Remarks: The value is given in analogy to the following substances: sodium acetate

Respiratory or skin sensitization

No data available

Germ cell mutagenicity

Test Type: Ames test
Test system: Salmonella typhimurium
Metabolic activation: Metabolic activation
Method: OECD Test Guideline 471
Result: negative
Remarks: The value is given in analogy to the following substances: sodium acetate
Test Type: in vivo assay
Species: Mouse
Cell type: sperm
Application Route: Oral
Result: negative
Remarks: (ECHA)
The value is given in analogy to the following substances: sodium acetate

Carcinogenicity

No data available

Reproductive toxicity

No data available

Specific target organ toxicity - single exposure

No data available

Specific target organ toxicity - repeated exposure

No data available

Aspiration hazard

No data available

11.2 Additional Information

Endocrine disrupting properties

Product:
Assessment : The substance/mixture does not contain components considered to have endocrine disrupting properties according to REACH Article 57(f) or Commission Delegated regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher.
Abdominal pain, Nausea, Vomiting
To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated.

SECTION 12: Ecological information

12.1 Toxicity

Toxicity to fish semi-static test LC50 - Danio rerio (zebra fish) - > 100 mg/l - 96 h (OECD Test Guideline 203)
Remarks: The value is given in analogy to the following substances: sodium acetate
Toxicity to daphnia static test EC50 - Daphnia magna (Water flea) - > 1.000 mg/l - 48 h and other aquatic (OECD Test Guideline 202) invertebrates Remarks: The value is given in analogy to the following substances: sodium acetate
Toxicity to algae ErC50 - Skeletonema costatum - > 1.000 mg/l - 72 h (ISO 10253)
Remarks: The value is given in analogy to the following substances: sodium acetate
Toxicity to bacteria static test EC50 - Pseudomonas putida - 7.200 mg/l - 16 h (DIN 38 412 Part 8)
Remarks: The value is given in analogy to the following substances: sodium acetate

12.2 Persistence and degradability

Biodegradability aerobic Dissolved organic carbon (DOC) - Exposure time 28 d
Result: 99 % - Readily biodegradable.
(Regulation (EC) No. 440/2008, Annex, C.4-A)
Remarks: The value is given in analogy to the following substances: sodium acetate

12.3 Bioaccumulative potential

No data available

12.4 Mobility in soil

No data available

12.5 Results of PBT and vPvB assessment

This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.

12.6 Endocrine disrupting properties

12.7 Other adverse effects

No data available

SECTION 13: Disposal considerations

13.1 Waste treatment methods

No data available

SECTION 14: Transport information

14.1 UN number

ADR/RID: -
IMDG: -
IATA: -

14.2 UN proper shipping name

ADR/RID: Not dangerous goods
IMDG: Not dangerous goods
IATA: Not dangerous goods

14.3 Transport hazard class(es)

ADR/RID: -
IMDG: -
IATA: -

14.4 Packaging group

ADR/RID: -
IMDG: -
IATA: -

14.5 Environmental hazards

ADR/RID: no
IMDG Marine pollutant: no
IATA: no

14.6 Special precautions for user

No data available
Further information: Not classified as dangerous in the meaning of transport regulations.

14.7 Maritime transport in bulk according to IMO instruments

Not applicable for product as supplied.

SECTION 15: Regulatory information

15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture

This material safety data sheet complies with the requirements of Regulation (EC) No.
1907/2006.

15.2 Chemical Safety Assessment

For this product a chemical safety assessment was not carried out

SECTION 16: Other information

Full text of other abbreviations

ADN - European Agreement concerning the International Carriage of Dangerous Goods by Inland Waterways
ADR - Agreement concerning the International Carriage ofDangerous Goods by Road
AIIC - Australian Inventory of Industrial Chemicals
ASTM -American Society for the Testing of Materials
bw - Body weight
CMR - Carcinogen,Mutagen or Reproductive Toxicant
DIN - Standard of the German Institute forStandardisation
DSL - Domestic Substances List (Canada)
ECx - Concentration associated with x% response
ELx - Loading rate associated with x% response
EmS -Emergency Schedule
ENCS - Existing and New Chemical Substances (Japan)
ErCx -Concentration associated with x% growth rate response
GHS - Globally HarmonizedSystem
GLP - Good Laboratory Practice
IARC - International Agency for Research onCancer
IATA - International Air Transport Association
IBC - International Code for theConstruction and Equipment of Ships carrying Dangerous Chemicals in Bulk
IC50 - Half maximal inhibitory concentration
ICAO - International Civil Aviation Organization
IECSC - Inventory of Existing Chemical Substances in China
IMDG - InternationalMaritime Dangerous Goods
IMO - International Maritime Organization
ISHL - IndustrialSafety and Health Law (Japan)
ISO - International Organisation for Standardization
KECI - Korea Existing Chemicals Inventory
LC50 - Lethal Concentration to 50 % of a test population
LD50 - Lethal Dose to 50% of a test population (Median Lethal Dose)
MARPOL - International Convention for the Prevention of Pollution from Ships
n.o.s. -Not Otherwise Specified
NO(A)EC - No Observed (Adverse) Effect Concentration
NO(A)EL - No Observed (Adverse) Effect Level
NOELR - No Observable Effect LoadingRate
NZIoC - New Zealand Inventory of Chemicals
OECD - Organization for EconomicCo-operation and Development
OPPTS - Office of Chemical Safety and PollutionPrevention
PBT - Persistent, Bioaccumulative and Toxic substance
PICCS - PhilippinesInventory of Chemicals and Chemical Substances
(Q)SAR - (Quantitative) StructureActivity Relationship
REACH - Regulation (EC) No 1907/2006 of the EuropeanParliament and of the Council concerning the Registration, Evaluation, Authorisation andRestriction of Chemicals
RID - Regulations concerning the International Carriage ofDangerous Goods by Rail
SADT - Self-Accelerating Decomposition Temperature
SDS -Safety Data Sheet
TCSI - Taiwan Chemical Substance Inventory
TECI - ThailandExisting Chemicals Inventory
TSCA - Toxic Substances Control Act (United States)
UN - United Nations
UNRTDG - United Nations Recommendations on the Transport ofDangerous Goods
vPvB - Very Persistent and Very Bioaccumulative

Disclaimer:

The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.